Fundamental Plumbing Tips for Bathtub Installation
Fundamental Plumbing Tips for Bathtub Installation
Blog Article
The article which follows in relation to Tools You Need to Install a New Bathtub is rather fascinating. You should look it over.
Setting up a bathtub isn't specifically brain surgery, however it does need strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a new one is additionally a moderately hard project. If the old bathtub is readily accessible, the project can relocate quickly; if you have to open up a wall to remove the old bathtub and position the brand-new bathtub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will certainly require a helper to move out the old bathtub and set in the new one. See to it you have actually qualified yourself for the job and are comfortable attempting it. Rather than hiring a specialist to take control of a halfway-completed job, it is better to consider employing one prior to you start. Possibilities are you may need a specialist plumber to make tube links.
This short article will help you mount a brand-new bathtub in your bathroom if you have already bought a brand-new tub and don't need to change the setup of your previous water supply pipelines.
Your devices and also product checklist ought to comprise the following:
Preparing for the Installment
First of all, the sustaining framework supplied with the bathroom ought to be fitted (if required) according to the producer's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to see to it that if the faucet comes with a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps device to avoid stress on the tub.
Fit the versatile tap ports to the bottom of the two taps making use of 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you use all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath should now prepare to be suited its final position.
Removing Old Taps
If you need to change old taps with new ones as a part of your installation, after that the first thing you must do is separate the supply of water. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The process of eliminating the existing taps can be fairly problematic because of the restricted access that is usually the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a cloth prepared for the staying water that will come from the pipelines. Once the supply pipelines have been removed, use the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this process. When the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned up of any old sealing substance.
Prior to moving on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Using the two wooden boards under its feet, place the bathtub in the needed position. The wood boards are practical in evenly spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four little factors.
The next goal is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bathtub up until the level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable faucet port to the proper supply pipeline by making a compression join; after that do the very same for the various other faucet.
Turn on the water and also inspect all joints as well as new pipework for leakages as well as tighten them if needed. Fill the bath tub as well as additionally examine the overflow outlet and the normal electrical outlet for leaks.
Lastly, fix the bath paneling as defined in the supplier's instruction manual. Tiling and also securing around the tub ought to wait till the bathtub has been made use of at least when as this will certainly settle it right into its final setting.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic adapter to stop damage to the string. One end of the connector fits on the plastic tail of the tap and the other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, then you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin ensuring that the washing machines are in place in between the tap and the sink. Safeguard the tap in position with the maker offered backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular tap connectors. The former type ought to be connected to the faucet ends initially, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture a rigid seal, causing the water to permeate the wall in between the bath and also the tiling, leading to problems with dampness as well as possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your components and fittings. They are offered in tubes and cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to always load the tub with water prior to securing, to enable the motion experienced when the tub remains in use. The sealant can crack rather early if you do not consider this activity prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly offered on the marketplace. It is suggested to fit the tiles using water-resistant or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed our piece on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you so much for taking the time to read our blog. Enjoyed our posting? Please share it. Let someone else discover it. I treasure reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Quick relief? Dial! Report this page